Motion
EP7041-3002
 
EP7041-3002 | Stepper motor module 50 V DC, 5 A, with incremental encoder, for high-speed applications
EP7041-3002
Connector
assignment
I/O
connection
M12 I/O
connection sockets 
Signal status display 
Labelling areas 
Power supply
status display:
Box supply (US
Auxiliary voltage (UP)
Power supply feed 
Power supply down- 
stream connection
1 | A1
2 | A2
3 | B1
4 | B2
5 | n. c.
1, 2 | V Motor
3, 4 | GND Motor
1 | +24 V DC Us
2 | Input B
3 | GND
4 | Input A
5 | Output
1 | GND
2 | V Enc
3 | A Enc
4 | B Enc
5 | C Enc
1 | Tx+
2 | Rx+
3 | Rx-
4 | Tx-
1 | + 24 V DC Us
2 | + 24 V DC UP
3 | GND
4 | GND
EtherCAT
signal input 
EtherCAT
signal output 
Stepper Motor
Motor supply
Digital inputs
Encoder
extended temperature range

EP7041-3002 | Stepper motor module 50 V DC, 5 A, with incremental encoder, for high-speed applications

The EP7041-3002 EtherCAT Box is intended for the direct connection of different stepper motors. The PWM output stages for two motor coils cover a wide voltage and current range. The EP7041-3002 can be adjusted to the motor and the application by changing just a few parameters. 256-fold micro-stepping ensures particularly quiet and precise motor operation. Connection of an incremental encoder enables a simple servo axis to be realised. Two digital inputs and a digital 0.5 A output enable connection of end switches and a motor brake.

The hardware- and software-based configuration make the stepper motor module particularly suitable for applications that are subject to unsteady motor operation due to natural resonance of the motor and the moved mass.

Technical data EP7041-3002
Number of outputs 1 stepper motor, 1 digital 24 V DC output
Number of inputs 2 digital inputs, encoder system (24 V DC encoder)
Connection method M12, screw type
Load type uni- or bipolar stepper motors
Nominal voltage 8…50 V DC
Distributed clocks yes
Protocol EtherCAT
Output current 2 x 3.5 A, 2 x 5 A peak current (overload- and short-circuit-proof)
Maximum step frequency 1000, 2000, 4000 or 8000 full steps/s (configurable)
Step pattern 256-fold micro stepping
Current controller frequency dynamic
Diagnostics LED error phase A and B, loss of step/stagnation, power, enable
Resolution approx. 5000 positions (per revolution, depending on motor and encoder type)
Bit width in the process image input/output: 2 x 16 bit data + 1 x 16 bit control/status
Electrical isolation 500 V
Current consumption from US 120 mA
Special features for high-speed applications, travel distance control, encoder input, load indication, motor supply via plug
Weight approx. 165 g
Operating/storage temperature -25…+60 °C/-40…+85 °C
Vibration/shock resistance conforms to EN 60068-2-6/EN 60068-2-27
EMC immunity/emission conforms to EN 61000-6-2/EN 61000-6-4
Protect. class/installation pos. IP 65/66/67 (conforms to EN 60529)/variable
Approvals CE, Ex
Accessories  
ZK1090-3xxx-xxxx Cables for EtherCAT signal in- and -output
ZK2020-3xxx-xxxx Cables for M8 power supply
AS2022-wGy0 stepper motor, 50 V DC, 1.37 Nm standstill torque, 5.6 A standstill current
AS2023-wGy0 stepper motor, 50 V DC, 2.3 Nm standstill torque, 5.0 A standstill current
AS2042-wGy0 stepper motor, 50 V DC, 6.4 Nm standstill torque, 6.0 A standstill current
Cables, gears and couplings accessories for AS2000 stepper motors
Further information Internet  
EP7041-3102 EtherCAT Box, industrial housing, Stepper Motor module 50 V DC, 5 A, 2 phases, with incremental encoder 5 V DC, 2 digital inputs 5 V DC, 1 digital output 24 V DC, for high speed applications
EP7041-2002 EtherCAT Box, industrial housing, Stepper Motor module 50 V DC, 5 A, 2 phases, with incremental encoder, 2 digital inputs 24 V DC, 1 digital output 24 V DC, motor connection via plug
EP7041-0002 stepper motor EtherCAT Box (industrial housing), IMAX = 5 A, 50 V, IP 67
EP7041-1002 EtherCAT Box, industrial housing, Stepper motor module, 50 V DC, 1.5 A, with incremental encoder, 2 digital inputs, 1 digital output
EL7041 stepper motor EtherCAT Terminal, IMAX = 5 A, 50 V, IP 20
EL7031 stepper motor EtherCAT Terminal, IMAX = 1.5 A, 24 V, IP 20