AT9011, AT9012
 
AT9011, AT9012 XTS movers

AT9011, AT9012 | XTS movers

The movers are made of a light and solid aluminium alloy. Thanks to their arrangement the rollers allow backlash-free travel on the straights and in the curves. The coating of the rollers causes very little running noise and is particularly low-wear without lubrication of the guide rail. The attractive forces of the magnetic plates are largely balanced by the opposed arrangement, so that the rollers and the rail do not have to absorb the comparatively high attractive forces of the magnets.

The centre of the encoder flag supplies a position signal to the motor module. The encoder flag is made from a sturdy, lightweight glass-fibre reinforced material. A Mover 1 can be detected by means of a special magnetic plate set. This mover is always recognised as servo axis 1 and used as the first servo axis after start-up. All following movers (standard movers) are counted upwards. This results in a fixed assignment between axis numbers and movers, which is even retained after the system has been switched off.

The AT9011-0070-0550 mover provides an increased payload due to its overall length of 70 mm and larger rollers. The standard rail can be used for traveling in straight lines, adapted rails are necessary for traveling around corners. Therefore, a mixed operation of movers of different sizes is only possible when traveling in straight lines.

 

Features

Ordering information XTS mover suitable for the guide rail system AT9000/AT9050
AT9011-0050-0550 mover, 6 rollers (plastic coated), length 50 mm, 410 g, mounted with magnetic plate set AT9001-0550 and set of rollers ZX9011-0050
AT9011-0050-1550 mover, 6 rollers (plastic coated), length 50 mm, 410 g, mounted with magnetic plate set AT9001-1550 and set of rollers ZX9011-0050
AT9011-0070-0550 mover, 6 rollers (plastic coated), length 70 mm, 595 g, mounted with magnetic plate set AT9001-0550 and set of rollers ZX9011-0070
AT9011-0070-1550 mover, 6 rollers (plastic coated), length 70 mm, 595 g, mounted with magnetic plate set AT9001-1550 and set of rollers ZX9011-0070
AT9012-0050-0550 mover, 12 rollers (plastic coated), length 50 mm, 460 g, mounted with magnetic plate set AT9001-0550 and set of rollers ZX9012-0050
AT9012-0050-1550 mover, 12 rollers (plastic coated), length 50 mm, 460 g, mounted with magnetic plate set AT9001-1550 and set of rollers ZX9012-0050
Accessories  
AT9001-0550 magnetic plate set mover standard, 5-pin, length 50 mm, preinstalled with 1.2 mm thick encoder flag, suitable for XTS standard movers
AT9001-0550-1840 magnetic plate set mover standard, 5-pin, length 50 mm, preinstalled with 1.8 mm thick encoder flag, suitable for external movers
AT9001-1550 magnetic plate set mover 1, 5-pin, length 50 mm, preinstalled with 1.2 mm thick encoder flag, suitable for XTS standard movers
AT9001-1550-1840 magnetic plate set mover 1, 5-pin, length 50 mm, preinstalled with 1.8 mm thick encoder flag, suitable for external movers
ZX9011-0050 set of rollers, 6 rollers (plastic coated), suitable for mover AT9011-0050-xxxx
ZX9011-0070 set of rollers, 6 rollers (plastic coated), suitable for mover AT9011-0070-xxxx
ZX9012-0050 set of rollers, 12 rollers (plastic coated), suitable for mover AT9012-0050-xxxx
Further XTS products  
AT20xx-0xxx XTS motor module
AT9xxx-xxxx XTS guide rails
AT2000-1500 starter kit large, 1500 mm straight length, 10 movers (AT9011-0050-0550)
TF5850-00pp TC3 XTS Extension

The magnetic plates can also be procured separately in order to be able to fit them to a self-developed mover. Technical boundary conditions and support on enquiry.