Ethernet TCP/IP Bus Terminal Controller BC9000
Power LEDs
K-bus
Bus Coupler
supply
Input for
power contacts
Power contacts
Ethernet RJ 45
Address selector
Configuration and
programming interface
extended temperature range

BC9000 | Ethernet TCP/IP Bus Terminal Controller

The BC9000 Bus Terminal Controller is a Bus Coupler with integrated PLC functionality and has a fieldbus interface for Ethernet. It is an intelligent slave that can be used as a non-central intelligence in the Ethernet system. One unit consists of the Bus Terminal Controller, any number of terminals between 1 and 64, and a bus end terminal.

The Bus Terminal Controller is programmed using the TwinCAT programming system according to IEC 61131-3. The configuration/programming interface of the BC9000 is used for loading the PLC program. If the software PLC TwinCAT is in use, the PLC program can also be loaded via Ethernet.

In the default setting the inputs and outputs of the connected Bus Terminals are assigned to the controller. Each Bus Terminal can be configured in such a way that it exchanges data directly through the fieldbus with the higher-level automation device.

Controller for distributed signal processing

The BC9000 and BC9050 Bus Terminal Controllers support the operation of all Bus Terminal types. As far as the user is concerned, the inputs and outputs are not handled any differently from the way they are by other coupler series. The information is made available for use as a byte array in the process image of the automation device.

The analog and multi-functional Bus Terminals can be adapted to each specific application using the KS2000 configuration set. Depending on the type, the analog Bus Terminals' registers contain temperature ranges, gain values and linearisation characteristics. With the KS2000, the required parameters can be set on a PC. The Bus Terminals store settings permanently and in a fail-safe manner.

Having the controller (PLC, IPC) carry out the configuration of the Bus Terminals is a further option. The PLC or IPC uses function blocks (FB) to take care of the configuration of all the peripherals during the start-up phase. The controller can, if required, upload the non-centrally generated configuration data in order to manage and store them centrally. This means that it is not necessary to carry out the setting procedure again if a Bus Terminal is exchanged. The controller carries out the desired setting automatically after switching on.

PLC data Ethernet TCP/IP | BC9000
Programming via TwinCAT and programming interface or Ethernet
Program memory 64/96 kbytes
Data memory 64/128 kbytes
Remanent data 4080 bytes
Runtime system 1 PLC task
PLC cycle time approx. 1.5 ms for 1,000 instructions (without I/O cycle, K-bus)
Programming languages IEC 61131-3 (IL, LD, FBD, SFC, ST)
Online change
Technical data BC9000
Number of Bus Terminals 64
Max. number of bytes fieldbus 512 byte input and 512 byte output
Max. number of bytes process image 512 byte input and 512 byte output
Digital peripheral signals 512 inputs/outputs
Analog peripheral signals 128 inputs/outputs
Protocol TwinCAT ADS, Modbus TCP
Configuration possibility via KS2000 or Ethernet
Data transfer rates 10/100 Mbaud, automatic recognition of the transmission rate
Bus interface 1 x RJ45
Power supply 24 V DC (-15 %/+20 %)
Input current 70 mA + (total K-bus current)/4, 500 mA max.
Starting current 2.5 x continuous current
Recommended fuse ≤ 10 A
Current supply K-bus 1750 mA
Power contacts 24 V DC max./10 A max.
Electrical isolation 500 V (power contact/supply voltage/fieldbus)
Weight approx. 170 g
Operating/storage temperature -25…+60 °C/-40…+85 °C
Protect. class/installation pos. IP 20/variable
Approvals CE, UL, Ex, GL
Accessories  
KS2000 configuration software for extended parameterisation
TwinCAT PLC programming system conforms to IEC 61131-3
Cordsets cordsets and connectors
FC9001-0010 | FC9011 Ethernet PCI fieldbus cards
Related products  
BC9050 Ethernet “Compact“ Bus Terminal Controller for up to 64 Bus Terminals (255 with K-bus extension)
BC9020 Ethernet TCP/IP “Economy plus” Bus Terminal Controller for up to 64 Bus Terminals (255 with K-bus extension)
BC9100 Ethernet TCP/IP Bus Terminal Controller for up to 64 Bus Terminals (with integrated 2-channel switch)
BC9120 Ethernet TCP/IP “Economy plus” Bus Terminal Controller for up to 64 Bus Terminals (255 with K-bus extension, with integrated 2-channel switch)
BX9000 Ethernet Bus Terminal Controller for up to 64 Bus Terminals (255 with K-bus extension)
BK9000 Ethernet TCP/IP Bus Coupler for up to 64 Bus Terminals
BK9050 Ethernet TCP/IP “Compact” Bus Coupler for up to 64 Bus Terminals (255 with K-bus extension)
CX8090 Ethernet Embedded PC
System  
Ethernet TCP/IP For further Ethernet TCP/IP products please see the system overview